25 Micron Stainless Steel Mesh Hydraulic Oil Filter Element R928028387 / 1.0012G25A005M for Rexroth Systems
Why Hydraulic Oil Filtration Decides Machine Life
Up to 80% of hydraulic component failures start with contaminated oil. Abrasive particles wear pump internals, stick directional valves and clog proportional controls long before a machine reaches its design life. The most cost-effective countermeasure is a correctly specified filter element — and for dirty, hot or remote installations, nothing beats a washable stainless steel mesh element.
Product Overview: R928028387 / 1.0012G25A005M
The R928028387 (element designation 1.0012G25A005M) is a cylindrical, pleated hydraulic oil filter element with 25 micron stainless steel wire mesh media. It is dimensioned as a direct interchange element for Rexroth / Bosch Rexroth filter housings, so it fits the existing bowl without any modification to the housing, bypass valve or clogging indicator.
Unlike disposable paper or glass-fibre cartridges, the metal mesh version can be cleaned and reused many times — typically 10 to 20 cleaning cycles instead of one. That makes it the preferred choice for heavy-duty machinery, remote sites, high-viscosity fluids and high-temperature circuits.

Key Features
- Filtration rating: 25 micron (beta 25(c) ≥ 200 per ISO 16889 on request)
- Media: multi-layer 304/316L stainless steel wire mesh, pleated for high dirt-holding capacity
- Pleat support: galvanised or stainless perforated cylinder, both ends resin-bonded
- High collapse pressure, suitable for return-line and pressure-line service
- Seals: NBR standard, FKM (Viton) for high temperature or aggressive fluids
- Tested to ISO 2941 (collapse), ISO 2942 (integrity), ISO 2943 (compatibility), ISO 16889 (efficiency)
- OEM-interchangeable geometry — no housing modification required
Technical Specifications
| Model / OEM reference | R928028387 — 1.0012G25A005M |
|---|---|
| Element type | Pleated cylindrical hydraulic filter element |
| Filtration rating | 25 micron |
| Filter media | Multi-layer stainless steel wire mesh (washable) |
| Collapse pressure | ≥ 210 bar (per OEM specification) |
| Operating temperature | -30 °C to +120 °C (fluid dependent) |
| Fluid compatibility | Mineral oil, HFC/HFD, water-glycol, biodegradable ester |
| Sealing material | NBR (standard) / FKM (optional) |
| Dimensions | OEM-interchangeable, confirmed against drawing before shipment |
| Packaging | Anti-static bag + carton, or neutral / private label |
Values above are typical for this element family. Exact outside diameter, inner diameter, height and flow rating are confirmed against your OEM drawing or sample before production.

Stainless Steel Mesh vs. Paper Media
- Washable and reusable — ultrasonic or solvent cleaning restores performance, cutting consumable spend dramatically.
- Stable micron rating — woven mesh is a fixed geometry, so the 25 micron rating does not drift as the element loads.
- High collapse and fatigue resistance — multi-layer sintered mesh survives pressure spikes and reverse-flow pulses without media rupture.
- Temperature and fluid tolerance — works with mineral oil, HFC/HFD fire-resistant fluids and water-glycol emulsions far beyond paper limits.
- No fibre migration — nothing sheds downstream into servo valves and proportional controls.
Typical Applications
- Hydraulic power units and central hydraulic systems
- Injection moulding machines, die-casting machines and hydraulic presses
- Excavators, wheel loaders, cranes and other mobile hydraulics
- Machine tools and servo or proportional-valve circuits
- Steel mills, mining equipment and marine deck machinery
- Wind-turbine pitch and gearbox lubrication circuits
Installation and Maintenance Best Practice
- Clean the housing bowl and seat before fitting a new or cleaned element; residual sludge re-contaminates the oil immediately.
- Lubricate the seals with system fluid, never grease.
- Record the pressure differential with a clean element — this is your baseline.
- Change or clean the element when differential pressure reaches the bypass setting (typically 2-3 bar on return filters) or twice the initial value.
- Clean metal mesh elements in an ultrasonic bath or filtered solvent, back-flushing from inside out, and dry before refitting. Never wire-brush the mesh.
- Replace at least once a year regardless of differential pressure, and always after a pump or motor failure.
Frequently Asked Questions
Is this a genuine Rexroth element?
We supply an OEM-interchangeable aftermarket element built to the same interface and performance specification. It fits the original housing without modification and is priced for series maintenance budgets.
Can a 25 micron element be washed and reused?
Only when it uses metal mesh media, as this one does. Paper and glass-fibre elements must never be washed — cleaning destroys the binder and releases fibres downstream.
What is the difference between 25 micron metal mesh and 25 micron glass fibre?
Glass fibre offers higher efficiency and holds more fine sludge; metal mesh offers repeatable geometry, unlimited cleaning cycles and better tolerance of pressure spikes and high temperature. For dirty, hot or remote installations, mesh usually wins on total cost of ownership.
Do you offer samples and custom labelling?
Yes. Free samples for evaluation, and neutral or private-label packaging with your own part number.
Request a Quotation
Send us the element photo, the housing nameplate and your required quantity. We will confirm the exact interchange, quote a factory-direct price and ship a sample for testing.Pls E-mail to nancy@airfilterbag.com.
Invia la tua richiesta direttamente a noi